Husqvarna Lawn Mower Accessory I0807213 User Manual

2008-01  
Illustrated  
Parts List  
I0807213  
531 30 70-05  
Sleeve Hitch  
(23 inch tire) (45-03021)  
Repair Parts Manual  
 
SAFETY RULES  
1. Readthisownersmanualandyourvehicleandimplement  
owners manuals before using this hitch.  
2. Do not allow children to operate vehicle or sleeve  
hitch.  
6. Before lowering and operating the implement, be sure  
no one is near the area of operation.  
7. Lower the sleeve hitch and implement when leaving  
vehicle unattended.  
8. Vehiclebrakingandstabilitymaybeaffected.Driveslowly  
when sleeve hitch and implement are in raised position.  
Stay off of steep slopes.  
3. Do not allow adults to operate the vehicle or sleeve hitch  
without proper instructions.  
4. Do not allow anyone to ride on sleeve hitch.  
5. Always place sleeve hitch in lowered position when  
attaching an implement.  
9. Keep all nuts and bolts tight and be sure the equipment  
is in safe operating condition.  
HARDWARE PACKAGE
(SHOWN FULL SIZE)  
A
B
C
D
F
E
O
N
P
L
I
G
Q
M
J
H
K
KEY QTY.  
DESCRIPTION  
KEY QTY.  
DESCRIPTION  
A
B
C
D
E
F
G
H
I
2
2
4
1
4
3
2
2
1
Hex Bolt, 5/8" x 2"  
Hex Bolt, 5/8" x 1-3/4"  
Hex Bolt, 3/8" x 1-1/4"  
Hex Bolt, 5/16" x 1"  
Carriage Bolt, 3/8" x 1"  
Clevis Pin  
Jam Nut, 5/8"  
Nylock Nut, 5/8"  
Nylock Nut 5/16"  
J
K
L
M
N
O
P
Q
4
4
4
2
1
1
3
1
Nylock Nut, 3/8"  
Hex Nut, 3/8"  
Lock Washer, 3/8"  
Flat Washer, 3/8"  
Spacer  
Spacer Plate  
3/32" Hair Cotter Pin  
5/32" Hair Cotter Pin  
NOTE: Bolt (C), Lock Washer (L) and Nut (K) will not be  
used unless the mounting holes in the tractor do not already  
contain bolts and nuts.  
2
 
IFYOUR TRACTOR LOOKS LIKE FIGURE 2A  
2. Install two 3/8" x 1-1/4" hex bolts in the left side of the  
tractor as shown.Attach the left (L.H.) Mounting Bracket  
(pin at top facing in) to the bolts using two 3/8" lock  
washers and 3/8" hex nuts. Repeat on the right side.  
See figure 2A.  
CARTON CONTENTS  
1
5
4
2
3
7
6
8
1. Sleeve Hitch Frame Assembly  
2. Mounting Bracket (R.H.)  
3. Mounting Bracket (L.H.)  
4. Lifting Link Plate  
5. Hitch Pin  
6. Lift Lever Assembly (with R.H. Pivot Bracket)  
7. L.H. Pivot Bracket  
FIGURE 2A  
8. Sleeve Hitch Lift Assembly  
I
F
Y
OUR TRACTOR LOOKS LIKE FIGURE 2B  
3. Remove
 
the nuts from the two bolts in each side of the  
tractor, leaving the bolts in place. See figure 2B.  
4. Attach the left (LH) and right (RH) Mounting Brackets to  
theboltsusingtheoriginalnutsandtwo3/8"atwashers.  
The brackets should angle outward with the weld pins  
at the top of the brackets facing inward. See figure 2B.  
NOTE:
If no bolt and nut are present in a hole, use a 3/8" x  
1-1/4" hex bolt, 3/8" lock washer and 3/8" hex nut to attach  
the Mounting Bracket to the hole.  
ASSEMB
L
Y  
TOOLS REQUIRED FOR ASSEMBLY  
(1) 1/2" Wrench or Adjustable Wrench  
(2) 9/16" Wrenches or Adjustable Wrenches  
(1) 15/16" Wrenches or Adjustable Wrenches  
1. Assemble a 5/16" x 1" hex bolt, a spacer and a 5/16"  
nylock nut to the three position slot in the R.H. pivot  
bracket on the left lever assembly. Use the position  
closest to the bend in the bracket (lowest implement  
depth setting). See figure 1.  
SPACER  
PIVOT  
BRACKET  
5/16" X 1"  
HEX BOLT  
5/16" NYLOCK  
NUT  
FIGURE 2B  
FIGURE 1  
3
 
5. Place the L.H. Pivot Bracket onto the end of the Lift  
Lever Assembly (the R.H. Pivot Bracket comes already  
installed on the assembly). See figure 3.  
6. Attach the R.H. and L.H. Pivot Brackets to the Sleeve  
Hitch Frame Assembly using four 3/8" x 1" carriage bolts  
and 3/8" nylock nuts. See figure 3.  
8. Assemble the two 5/8" jam nuts halfway onto the two  
5/8" x 2" hex bolts. Screw the bolts into the nuts that are  
welded to the Sleeve Hitch Lift Assembly. Tighten the  
jam nuts against the welded nuts. See figure 5.  
9. AssembletheliftinglinktotheSleeveHitchLiftAssembly  
usinga5/8"x1-3/4"hexboltanda5/8"nylocknut.Usethe  
bottom hole in the lifting link (gives the lowest implement  
depth setting). Tighten the nut only until snug. Do not  
squeeze the welded arms together. See figure 5.  
L.H. PIVOT BRACKET  
R.H. PIVOT BRACKET  
LIFT LEVER  
ASSEMBLY  
3/8-16 x 1"  
CARRIAGE  
BOLT  
3/8" NYLOCK NUT  
SLEEVE HITCH FRAME  
FIGURE 3  
7. Hook the Sleeve Hitch Frame Assembly onto the weld  
pins in the mounting brackets. Attach the bottom of the  
Assembly to the tractor hitch using a 5/8" x 1-3/4" hex  
bolt and a 5/8" nylock nut. See figure 4.  
NOTE: If your tractor hitch has ridges that prevent the  
sleeve hitch assembly from resting flat, place the spacer  
plate underneath the sleeve hitch assembly.  
FIGURE 5  
10. Attach the Sleeve Hitch Lift Assembly to the Sleeve  
Hitch Frame Assembly using three 5/8" x 1-3/4" clevis  
pins and 3/32" hair cotter pins as shown in figure 6.  
11. Install the hitch pin in the sleeve hitch and secure it with  
the 5/32" hair cotter pin. See figure 6.  
SLEEVE HITCH  
FRAME ASSEMBLY  
LIFT LEVER  
ASSEMBLY  
HITCH PIN  
HEX BOLT  
5/8" x 1-3/4"  
5/32" HAIR  
COTTER PIN  
SPACER PLATE  
(SEE NOTE)  
(3) 3/32" HAIR  
COTTER PINS  
WELD  
PIN  
5/8" NYLOCK NUT  
(3) CLEVIS PINS  
FIGURE 4  
FIGURE 6  
4
 
OPERATION  
1. Move the lift lever backward to lower the sleeve hitch.  
2. Attach an implement using the sleeve hitch pin.Tighten  
the 5/8" x 2" stabilizer bolts against the implement hitch  
and then tighten the jam nuts. See figure 5 on page 4.  
IMPORTANT: Some implements may require that the  
stabilizer bolts not be tightened. Refer to your implement  
owner's manual.  
3. The sleeve hitch is assembled in the lowest position by  
theassemblyinstructions.Iftheimplementattachedtothe  
sleeve hitch is not level front to back during operation:  
a. Move the hex bolt in the lifting link to a hole (3 holes  
available) that gives better levelling.  
b. For closer adjustment, move the hex bolt assembled  
in figure 1 to a position in the three position slot that  
gives better levelling.  
4. To tow an implement that has a tow hitch, simply remove  
three clevis pins and then remove the Sleeve Hitch Lift  
Assembly from the Sleeve Hitch Frame Assembly.  
5. To remove the entire Sleeve Hitch attachment, remove  
the5/8"x1-3/4"hexboltand5/8"nylocknutwhichfasten  
the bottom of the sleeve hitch to the tractor hitch, then  
lift the attachment off the tractor.  
MAINTENANCE  
1. Clean off after each use.  
2. Oil pivot points as needed.  
3. Store in a dry location.  
5
 
RE
P
A
IR
P
A
RTS FOR MODEL 45-03021 SLEEVE HITCH  
27  
26  
16  
20  
24  
25  
21  
3
19  
18  
17  
4
7
1
12  
8
11  
15  
A
11  
23  
15  
9
14  
2
10  
12  
A
5
13  
22  
13  
11  
15  
6
Ref Part No. Qty Description  
Ref Part No. Qty Description  
1
2
3
4
5
6
7
8
9
65409  
25715  
25714  
43350  
HA21362  
65404  
64625  
24732  
47947  
1
1
1
4
4
1
1
1
2
2
3
2
2
1
Sleeve Hitch Frame  
Pivot Bracket, Left  
Pivot Bracket, Right  
Bolt, Carriage 3/8-16 x 1"  
Hex Lock Nut, 3/8-16  
Sleeve Hitch Lift Assembly  
Lift Lever Assembly  
Lifting Link Plate  
Bolt, Hex 5/8-11 x 2"  
Hex Jam Nut, 5/8-11  
Clevis Pin, 5/8" x 1-3/4"  
Bolt, Hex 5/8-11 x 1-3/4"  
Nylock Nut, 5/8-11  
15  
16  
17  
18  
19  
20  
21  
43343  
46471  
43063  
23625  
47810  
65370  
65369  
3
1
1
1
1
1
1
1
1
2
4
4
4
1
Pin, Hair Cotter 3/32"  
Grip, Plastic  
Bolt, 5/16-18 x 1"  
Spacer  
Nylock Nut, 5/16"  
Mounting Bracket, Right  
Mounting Bracket, Left  
Pin, Hair Cotter, 5/32"  
Spacer Plate  
22 714-0117  
23  
24  
25  
26  
27  
25685  
43070  
43087  
43003  
43015  
49949  
10 712-0242  
11 HA3980  
12  
13 712-0261  
14 47950  
Flat Washer  
Bolt, Hex 3/8-16 x 1-1/4"  
Lock Washer, 3/8"  
Hex Nut, 3/8-16  
47951  
Pin, Sleeve Hitch  
Owner's Manual  
6
 
7
 
the fastest way to purchase parts www.speedepart.com  
REPAIR PARTS  
Agri-Fab, Inc.  
809 South Hamilton  
Sullivan, IL. 61951  
217-728-8388  
© 2004 Agri-Fab, Inc  
 

Graco Bouncy Seat ISPA173AA User Manual
Harbor Freight Tools Saw 69438 User Manual
Harbor Freight Tools Vacuum Cleaner 3394 User Manual
Hasselblad Camera Lens 0 5 User Manual
Hearth and Home Technologies Egg Cooker BH 105 User Manual
Hotpoint Oven SD97 User Manual
HP Hewlett Packard Respiratory Product 60 HP User Manual
HP Hewlett Packard Telephone Premium Travel Phone User Manual
Husqvarna Snow Blower 1130SB User Manual
Iiyama Computer Monitor E1780SD B1 User Manual