Harbor Freight Tools Drill 42977 User Manual

Stand for  
Drill / Mill  
Machine  
Model 42977  
A s s e m b l y & O p e r a t i n g  
I n s t r u c t i o n s  
Stand shown with Drill / Mill machine (not included)  
®
3491 Mission Oaks Blvd. / Camarillo, CA 93011  
Copyright © 2000 by Harbor Freight Tools®. All Rights Reserved.  
No portion of this manual or any artwork contained herein may be reproduced in any  
manner, shape or form without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353.  
REVISED 08/05  
 
ASSEMBLYAND OPERATINGINSTRUCTIONS  
Your machine stand is fully assembled when you  
receive it. However, it must be attached to the floor,  
and the machine must be mounted on it prior to  
operation.  
1.  
Find a location for the stand within your  
workshop. Select a location which has a sturdy,  
level floor which is capable of supporting the  
weight of the stand, machine to be mounted on it,  
and any workpieces you intend to place on the  
machine or stand.  
2.  
The location must also provide safe working  
conditions, including adequate light and  
ventilation, protection from water and weather,  
and acess to an appropriate power supply for the  
machine.  
G
F
1
E
3.  
4.  
Locate the stand in an area that provides  
adequate working room to manage the  
workpieces, tools, equipment and supplies  
needed to perform the intended operations.  
Prepare the floor by leveling it, using cement,  
steel plates, wooden reinforcements or other  
suitable means.  
A
D
2
3
C
B
Figure 1. Assembly Diagram  
5.  
6.  
7.  
Place the stand in its intended location, and mark the floor through the bolt holes in the flanges on the  
corners of the base.  
Depending on the floor material, drill bolt holes or install lag bolts in the floor. Secure these as  
appropriate.  
Reposition the stand on the prepared floor fastening system, and secure in place. Test the stand to be  
sure it is permanently and securely attached before placing the machine on the stand.  
Your Drill / Mill machine may include a tray which must be positioned between the machine and the  
stand. Numbers shown below refer to the diagram in Figure 1.  
1.  
Place the tray (#5) (not included) on the stand, aligning the four holes in the corners with the mounting  
holes on the upper flange of the stand.  
2.  
With the help of an assistant, place the machine on the tray, with the mounting holes in the machine base  
(#6) (not included) aligned with the holes in the tray and the stand.  
3.  
4.  
Fasten the machine securely to the stand, using four bolts (#7), washers and nuts (not included).  
Check to be sure the machine is securely mounted before connecting the power cord, or turning it on.  
NOTE: Some parts are listed and shown for illustration purposes only  
and are not available individually as replacement parts.  
Page 3 SKU # 42977  
 
#42977 DRILL / MILL MACHINE STAND PARTS DIAGRAM  
P/N DESCRIPTION  
1
2
3
4
Body  
Door  
Hinge  
G
F
1
Door HandleAssembly  
A B C D E F  
E
A
D
DOOR HANDLE  
ASSEMBLY  
P/N DESCRIPTION  
2
3
C
B
A
B
C
D
E
F
Bolt  
Spring  
Handle  
Sleeve  
Door Holder  
SpringWasher  
Nut  
G
MAINTENANCE  
Keep the stand wiped down and clean.  
Do not allow the stand to remain wet, and do not allow standing water to accumulate around the base.  
Use applications of light grease or paint to any unpainted surfaces to prevent rust.  
Check the floor mounting bolts and machine mounting bolts monthly to assure that they remain securely  
fastened. Retighten or replace any fastening hardware as needed.  
1.  
2.  
3.  
4.  
WARNING!  
USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the work  
of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool  
and do not use this tool for a purpose for which it was not intended.  
PLEASE READTHE FOLLOWINGCAREFULLY  
THE MANUFACTURERAND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUALASA  
REFERENCE TOOLONLY: NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKESANYREPRESENTATION  
OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO  
THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACEANYPARTS OF THE PRODUCT: IN FACTTHE  
MANUFACTURER A ND/OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND PARTS  
REPLACEMENTS SHOULD BE UNDERTAKEN BYCERTIFIEDAND LICENSED TECHNICIANSAND NOT BYTHE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITYARISING OUT OF HIS OR HER REPAIRS TO THE  
ORIGINALPRODUCT OR REPLACEMENT PARTS THERETO, ORARISING OUT OF HIS OR HER INSTALLATION  
OF REPLACEMENT PARTS THERETO.  
REV 09/06  
Page 4 SKU # 42977  
 

Hans Grohe Plumbing Product 28518XX1 User Manual
Harbor Freight Tools Nail Gun 67450 User Manual
Hearth and Home Technologies Indoor Fireplace 6000GLX IPILP R User Manual
Hotpoint Dishwasher FDEF 4101 User Manual
Hotpoint Washer WMFG 611 User Manual
Huawei Cell Phone P6 User Manual
Huawei Telephone F610 User Manual
Hunter Fan Fan 22437 User Manual
Hyundai Microwave Oven MWEGH 281S User Manual
iHome Clock Radio iP40 User Manual