TRAILER
SPARE TIRE CARRIER
93341
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
10. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Non-Skid
footwear is recommended when assembling and when using the Spare Tire Carrier. Wear restrictive hair
covering to contain long hair.
11. Do not force this product. Do not use inappropriate attachments in an attempt to exceed the capacity of the
SpareTire Carrier.
12. Keep children away. Children must never be allowed in the work area.
13. Make certain that no persons or pets are under theTrailer Carrier orTrailer during loading.
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Specific Trailer Tire Carrier Warnings and Precautions
1. Read and understand all instructions and safety precautions as outlined in the manufacturer’s manual
for the trailer you are using. Make sure to mount the Trailer Carrier to the manufacturer’s recommended
mounting points.
2. Examine theTrailer SpareTire Carrier for structural cracks, bends, damage and any other condition
that may affect the safe operation of the product. Do not use if damaged in any way.
3. Always keep hands, fingers,arms and feet out from under theTrailer SpareTire Carrier when the trailer
is moving.
4. It is the trailer owner’s responsibility to make sure the usage of this product meets all local motor
vehicle laws and regulations. Do not obscure marker, tail or running lights or license plate.
5. Make certain bracket or tire does not interfere with the trailers normal movement or blocks the driver’s
view.
6. For safety,it is recommended that 2 people install this product.
Unpacking
When unpacking your Trailer Spare Tire Carrier, make certain that all parts on page 5 of this manual
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
SKU 93341
For technical questions, please call 1-800-444-3353.
Page 3
Installation
1. Secure the unloaded trailer with wheel chocks (blocks) on a hard, flat surface capable of supporting the
weight of the trailer, Trailer SpareTire Carrier and required tools.
2. Raise the trailer tongue and secure it with two supports, one on each side of the trailer tongue.
3. Position the Mounting Bracket (2) in the correct location against the side of the trailer tongue.
Note: The spare tire will be located to the side of the trailer tongue.
Note: The angled Tire Mounting Plate should be angled upward (above) the position of the Trailer Tongue
Plate.
4. Attach the Mounting Bar (1) to the Mounting Bracket (2). Set the Mounting Bars (1) (containing six holes) flat
against the trailer tongue so that the edges of the Mounting Bars (1) curve out away from the trailer tongue.
Insert four Hex Bolts (3) through the Mounting Plates (1) as close to the trailer tongue as possible. Slide on
Washers (8), Spring LockWashers (7) and thread on Nut (6). Use a torque wrench to tighten the Nuts (6) to 90
ft./Lbs.
5. Mount the tire on the Tire Mounting Plate with the valve facing outward so that the tire air pressure can be
checked at any interval.
Warning:
Make certain that the tire is centered on the Tire Carrier when mounted-see
Figure 1.
6. Insert Round Head Bolts (4) up through theTire Mounting Plate and through theWheel. Thread on Nylon Lock
Nuts (5)-see Assembly diagram. Securely tighten and torque all hardware to 90 ft./lbs.
Figure 1
unbalanced over Carrier
balanced over Carrier
Tire Mounting Plate
Maintenance
Before each use, inspect the SpareTire Carrier for its general condition. Check for loose bolts, cracked,
bent or broken parts and any other condition that may affect its safe operation.
REV 01/06
SKU 93341
For technical questions, please call 1-800-444-3353.
Page 4
Parts List
Part # Description
Quantity Part # Description
Quantity
1
2
3
4
Mounting Bar
Mounting Bracket
Hex Bolt
2
1
4
2
5
6
7
8
Nylon Lock Nut
Nut
Spring Lock Washer 4
2
4
Round Head Bolt
Washer
4
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Parts Assembly Diagram
1
4
3
Tire
Mounting
Plate
5
Trailer
Tongue
Plate
8
2
7
6
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
REV 01/06
SKU 93341
For technical questions, please call 1-800-444-3353.
Page 5
|