Graco Universal Remote 307016T User Manual

Instructions - Parts  
Fluid Controls and  
Fittings  
307016T  
EN  
Part No. 223627, 208085, 223621, 208082, 223622, 223623, 223624, 208250,  
214019, 223626, and 210097  
200 psi (1.4 MPa, 14 bar) Maximum Inbound Fluid Pressure  
Part No. 223625 and 223628  
300 psi (2.1 MPa, 21 bar) Maximum Inbound Fluid Pressure  
See page 2 for model information  
Important Safety Instructions  
Read all warnings and instructions in this  
manual. Save these instructions.  
ti02286a  
 
Warnings  
Warnings  
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-  
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When  
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific  
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where  
applicable.  
NOTE: The following warning applies only to Models 214018, 208250, 214019, and 210097, which contain alu-  
minum housings.  
WARNING  
PRESSURIZED ALUMINUM PARTS HAZARD  
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical  
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or prop-  
erty damage.  
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or  
fluids containing such solvents.  
Many other fluids may contain chemicals that can react with aluminum. Contact your material sup-  
plier for compatibility.  
307016T  
3
 
 
Installation  
Installation  
Service  
Connect the Fluid Hose  
To reduce the risk of serious injury, including  
splashing in the eyes or on the skin, always shut off  
the air and fluid pressure to the gun and trigger the  
gun to relieve pressure in the hoses before  
Regulators or Circulating Adapters  
Connect the fluid hoses to the 1/4 npsm(m) inlet and  
return fittings.  
disconnecting hoses from the regulator or adapter.  
Straight Adapter  
Connect a hose to the 3/8 npsm(m) inlet fitting.  
To Clean or Service the  
Regulator  
Connect the Regulator or  
Adapter to the Gun  
1. Relieve the air and fluid pressures.  
2. Disconnect the regulator from the gun and the  
hoses from the regulator.  
Model 223622  
3. Disassemble the regulator. Refer to the Parts Draw-  
ing.  
Screw the regulator union adapter onto the gun fluid  
inlet.  
4. Clean and inspect the parts carefully.  
Models with Twist-lock Couplers  
5. Replace worn or damaged parts and reassemble  
the regulator. Be sure the nylon side of the dia-  
phragm (12) faces the fluid.  
Screw the coupler stem onto the gun inlet. Connect  
the twist-lock couplers by lining up the coupler slots  
with the pins on the stem, pushing the coupler onto  
the stem, then twisting the coupler clockwise to lock  
it.  
Torque Notes:  
Diaphragm Nut (3) onto Valve Stem (8):  
6 to 10 in-lb (0.7 to 1.1 Nm)  
Models with Slip-ring Couplers  
Pull the slip ring back as you push the coupler onto  
the stem.  
Screws (5) into the Housing (18):  
20 to 30 in-lb (2.3 to 3.4 Nm)  
Cap (14) into the Housing (18):  
10 to 15 ft-lb (13.5 to 20.0 Nm)  
Operation  
NOTICE  
To avoid damaging the regulator diaphragm, never  
exceed 200 psi (1.4 MPa, 14 bar) Maximum Inbound  
Fluid Pressure to the regulator.  
To Adjust the Fluid Pressure  
Trigger the gun. Turn the fluid regulator setscrew (2)  
clockwise to the desired setting. Release the gun trig-  
ger, tighten the locknut (1), and install the acorn nut  
(16).  
4
307016T  
 
     
Parts  
Parts  
Ref.  
Ref.  
No. Part No. Description  
Qty.  
No. Part No. Description  
Qty.  
28  
29  
168891 SPRING, compression  
SLIP RING COUPLER ASSY.  
Includes items 30-34  
1
1
1
2
100166 NUT, hex mach; No. 10-32  
102433 SCREW, set, hex socket;  
No. 10-32 x 3/4”  
1
1
30  
100172 BALL; chrome alloy,  
0.188" (4.76 mm) dia.  
3
3
102980  
1
NUT, hex; stainless steel;  
No. 4-40  
31157230 RING, retaining  
1
1
1
1
1
1
4*  
5
102982 O-RING; PTFE  
103229  
1
5
32  
33  
34  
168874 RING, coupler  
168875 SPRING, compression  
HOUSING, coupler  
SCREW, cap, socket head;  
No. 8-32 x 3/8”  
6
7
8
167244 RETAINER, spring  
167245 SPRING, compression  
168872 VALVE STEM  
1
1
1
1
1
1
1
1
1
1
1
1
1
35168882 GASKET; acetal  
36  
223892 UNION, adapter; 3/8” npsm(f)  
swivel  
9
10*  
11  
168877 HOUSING, upper  
178320 GASKET; cellulose fibre  
168879 WASHER, back-up  
37** 178846 SEAL; nylon  
38** 103075 BALL; stainless steel,  
0.438" (11.1 mm) dia.  
39** 178847 GUIDE, coupler stem  
40** 178848 BALL SEAT; PTFE  
41111279 BALL; stainless steel,  
0.438" (11.1 mm) dia.  
1
1
12*† 178321 DIAPHRAGM; nylon & buna-n  
1
1
1
13*  
14  
15*  
16  
17*  
18  
168881 WASHER; acetal  
168884 CAP  
169597 VALVE SEAT  
170303 ACORN NUT; No. 10-32  
178322 GASKET; cellulose fibre  
208086 HOUSING, lower;  
Models 223621, 208082, &  
223622 only  
Recommended “tool box” spare parts. Keep  
these spare parts on hand to reduce down time.  
These parts are included in Repair Kit 208380,  
which may be purchased separately.  
These parts are included in Repair Kit 217502,  
which may be purchased separately.  
These parts are included in Repair Kit 210786,  
which may be purchased separately.  
Accessory PTFE Diaphragm 185028 with PET  
Backing Diaphragm 168880 is available. See  
page 10.  
*
**  
208180 HOUSING, lower;  
Model 223623 only  
19† 101947 BALL; stainless steel;  
0.375" (9.5 mm) dia.  
1
1
20  
186203 COUPLING NUT; stainless steel  
1
1
1
1
1
1
1
21† 104338 SEAL, spring loaded; PTFE  
22† 171887 BALL SEAT; PTFE  
23† 171888 HOUSING, seal; acetal  
24  
186202 HOUSING, coupler; stainless steel  
168890 SPRING, compression  
VALVE SEAT; acetal  
These parts are included in Repair Kit 24U819,  
which may be purchased separately.  
25  
26■  
307016T  
5
 
 
Parts  
Coupler Stems  
223627  
208085  
223628  
Ref.  
No. Part No. Description  
Qty.  
1✓  
2
3
103337 O-RING; fluoroelastomer  
168868 FITTING, coupler  
168869 COUPLING NUT; 3/8 npsm (f)  
1
1
1
2
3
1
Fluid Regulators  
Model 223622 Series A  
Model 223621 Series A  
Model 208082 Series E  
Model 223623 Series A  
Includes items 1-18, 35, 36  
Includes items 1-25  
Includes items 1-19, 26-34  
Includes items 1-18, 20, 24,  
25, 37-40  
20  
24  
31  
20  
24  
36  
32  
29■  
8
26■  
35  
39**  
37**  
40**  
33  
34  
30  
†23  
†21  
†22  
†19  
7
19  
28  
41  
25  
25  
Common Parts for Regulators  
18  
*4  
8
11  
10*  
17*  
2
14  
3
12*†  
13*  
*15  
NOTES  
Small hole faces down  
1
2
3
4
5
6
7
8
7
9
6
Torque to 10–15 ft/lb (13.5–20 N•m)  
Nylon side MUST face fluid  
1/4 npsm(m)  
6
5
4
1
3
5
Torque to 6-10 in/lb (0.7-1.1 N•m)  
Torque to 20-30 in/lb (2.3-3.4 N•m)  
Spring inside faces down  
16  
2
Large chamfer faces up  
02287a  
6
307016T  
 
Parts  
Straight Adapters  
NOTES  
3/8 npsm(m)  
1
2
3
Spring inside faces down  
Torque to 15-25 ft/lb (20-34 N•m)  
Model 223624 Series A  
TWIST LOCK COUPLER  
Includes items 3-13  
3
3
4
†13  
2
†10  
†12  
†9  
7
11  
1
02293a  
Ref.  
Ref.  
No. Part No. Description  
Qty.  
No. Part No. Description  
Qty.  
10† 104338 SEAL, spring loaded; PTFE  
1
1
1
1
3
186203 COUPLING NUT; stainless steel  
186202 HOUSING, coupler; stainless steel  
168890 SPRING, compression  
101947 BALL; stainless steel;  
0.375" (9.5 mm) dia.  
1
1
1
1
11  
170755 HOUSING, straight adapter  
4
7
9†  
12† 171887 BALL SEAT; PTFE  
13† 171888 HOUSING, seal; acetal  
These parts are included in Repair Kit 210786,  
which may be purchased separately.  
307016T  
7
 
Parts  
Straight Adapters  
Model 223625 Series A  
TWIST LOCK COUPLER  
Model 208250 Series B  
SLIP RING COUPLER  
Includes items 3, 4, 7, 24 - 27  
Includes items 8, 9, 14 - 22  
4
3
19  
4
17  
14  
20  
25  
24  
26  
21  
2
3
22  
18  
9
28  
16  
7
8
NOTES  
27  
3/8 npsm(m)  
1
2
3
4
02296a  
Small hole faces down  
1
1
Large chamfer faces up  
02294a  
Torque to 15-25 ft-lb (20-34 N•m)  
Ref.  
No. Part No. Description  
Ref.  
Qty.  
No. Part No. Description  
Qty.  
21  
22  
24  
25  
26  
27  
168875 SPRING, compression  
HOUSING, coupler  
178846 SEAL; nylon  
178847 GUIDE, coupler stem  
178848 BALL SEAT; PTFE  
180050 HOUSING, straight adapter  
1
1
1
1
1
1
1
3
4
7
8
9✓  
186203 COUPLING NUT; stainless steel  
186202 HOUSING, coupler; stainless steel  
168890 SPRING, compression  
169472 HOUSING, straight adapter  
101947 BALL; stainless steel;  
0.375" (9.5 mm) dia.  
1
1
1
1
1
28111279 BALL; stainless steel,  
14■  
16  
17■  
VALVE SEAT; acetal  
1
1
0.438" (11.1 mm) dia.  
Recommended “tool box” spare parts. Keep on  
168891 SPRING, compression  
SLIP RING COUPLER ASSY.  
Includes items 18-22  
100172 BALL; chrome alloy,  
0.188" (4.76 mm) dia.  
hand to reduce downtime.  
These parts are included in Repair Kit 24U819,  
which may be purchased separately.  
18  
3
19157230 RING, retaining  
20 168874 RING, coupler  
1
1
8
307016T  
 
Parts  
Circulating Adapters  
Model 214019 Series B  
TWIST LOCK COUPLER  
Model 223626 Series A  
TWIST LOCK COUPLER  
Model 210097 Series B  
TWIST LOCK COUPLER  
Includes items 2, 3, 7 - 11, 15, 16  
Stainless Steel  
Includes items 2, 3, 7, 8, 26 - 30  
Includes items 4, 5, 7, 8, 10 - 16  
4
2
4
2
4
4
7
5
7
†16  
†16  
†11  
28**  
27**  
†11  
†15  
2
†15  
†10  
29**  
3
26**  
8
†10  
8
8
30  
12  
13  
9
3
3
Small hole  
faces down  
02297a  
1
02298a  
1
02300a  
14  
1
NOTES  
1/4 npsm(m)  
Small hole faces down  
1
3
4
Spring inside faces down  
Torque to 15–25 ft/lb (20–34 N•m)  
2
Ref.  
Ref.  
No. Part No. Description  
Qty.  
No. Part No. Description  
Qty.  
16† 171888 HOUSING, seal; acetal  
26** 103075 BALL; stainless steel,  
0.438" (11.1 mm) dia.  
1
1
2
3
4
5
7
8
9
167394 COUPLING NUT  
1
2
1
1
1
1
1
1
167395 HOSE ADAPTER; 1/4 npsm(m)  
186203 COUPLING NUT; stainless steel  
186202 HOUSING, coupler; stainless steel  
181578 HOUSING, coupler  
27** 178846 SEAL; nylon  
1
1
1
1
28** 178847 GUIDE, coupler stem  
29** 178848 BALL SEAT; PTFE  
168890 SPRING, compression  
169473 HOUSING, circulating adapter  
30  
169471 HOUSING, circulating adapter  
10† 101947 BALL; stainless steel;  
0.375" (9.5 mm) dia.  
11† 104338 SEAL, spring loaded; PTFE  
12  
13  
14  
These parts are included in Repair Kit 210786,  
which may be purchased separately.  
** These parts are included in Repair Kit 217502,  
which may be purchased separately.  
1
1
1
2
1
170755 HOUSING, straight adapter  
171233 HOUSING, circulating adapter  
171234 HOSE ADAPTER; 1/4 npsm(m)  
15† 171887 BALL SEAT; PTFE  
307016T  
9
 
Accessories  
Accessories  
Accessories must be purchased separately  
PTFE Diaphragm 185028, with PET Backing  
Diaphragm 168880*  
Use when regulator must be submersed in a solvent  
incompatible with the buna-n backing of the standard  
diaphragm 178321.  
*
The PTFE diaphragm must face the fluid, with the  
PET diaphragm used as backing.  
10  
307016T  
 
 
Accessories  
307016T  
11  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs  
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
For the latest information about Graco products, visit www.graco.com.  
For patent information, see www.graco.com/patents.  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 307016  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 1997, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revision T, November, 2013  
 
 

Grizzly Glue Gun H8175 User Manual
Grizzly Saw G1022PRO User Manual
Hamilton Beach Air Cleaner 840121000 User Manual
Hasbro Games 07951 User Manual
Hasbro Games Men in Black User Manual
Hasselblad Car Video System CF22 CF39 User Manual
Heartland Stove Wood Stove User Manual
Hotpoint Dishwasher DWF40 User Manual
HP Hewlett Packard Security Camera XP256 User Manual
Hustler Turf Lawn Mower Super ZT User Manual