Graco TV Cables 24P686 User Manual

Instructions  
GLC 2200 Wiring  
Connector Kit  
3A2992B  
EN  
Used to interface the GLC2200 Lubrication Controller to pump and pump accessories. For  
professional use only.  
Not approved for use in explosive atmospheres or hazardous locations.  
Kit Nos.:  
Single Connector Kit: 24P686  
Multiple (5) Connectors Kit: 24P687  
Kits are rated IP65.  
make  
Important Safety Instructions  
Read all warnings and instructions in this  
manual and the GLC 2200 Lubrication  
Controller instruction manual included with your  
unit. Save these instructions.  
 
Instructions  
Component Wiring  
1. Before connecting wires to components verify the  
Connector end of the cable is NOT plugged into the  
GLC2200 controller.  
4. Using the Wiring Key Table, connect components to  
wires matching each wire color and pin location.  
Verify all negative and positive wire colors are cor-  
rectly assigned.  
2. Remove 2 to 3 inches of the outer insulation (a)  
from bare end of the cable as shown FIG. 4.  
NOTE: The second column of the Wiring Key Table  
is provided for the user to record the wire color  
assigned to each component.  
.
5. Plug connector into the GLC2200 unit matching pin  
numbers to Connector Identification Label.  
a
NOTE: The connector can only be plugged into the  
GLC2200 one way. The clip (c) should be facing  
down when the connector is correctly oriented.  
FIG. 4  
3. Strip each wire (b) you are using for the installation  
as shown in FIG. 5.  
NOTE: It is not necessary to strip all of the wires;  
only strip the wires needed for your installation.  
c
b
FIG. 6  
FIG. 5  
Wiring Diagram  
1
6
2
7
3
8
4
9
5
-
+
M
10  
V
9A Fuse  
FIG. 7  
M = Motor pump power or solenoid  
V = Electric vent valve for injector-based systems  
3A2992B  
3
 
   
Wiring Key  
Connector Identification Label  
(Adhered to GLC2200 controller)  
Wire  
Color*  
+/-  
-
Pin  
Description  
PIN  
1
2
3
4
5
1
2
Pump  
Alarm  
-
9A  
2A  
-
3
Low Level  
+9V  
P/C  
-
4
Pressure Cycle Switch  
Voltage Input  
Pump  
+30V  
-
5
PIN  
6
7
8
9
10  
+
+
+
+
+
6
7
Alarm  
8
Low Level  
9
Pressure Cycle Switch  
Voltage Input  
10  
* Use this column to record the wire color assigned to  
each component used for your installation.  
Parts  
Accessories  
Qty  
Ref Description  
24P686 24P687  
Crimping Tool - 16T671  
PIN, socket, 18-24 AWG,  
crimp, gold  
1
2
12  
1
60  
5
CONNECTOR, receptacle,  
dual, 10 position  
1
2
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 3A2992  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
December 2013  
 
 

Grizzly Nail Gun G3690 User Manual
Grizzly Outdoor Cart H0760 User Manual
Harbor Freight Tools Air Compressor 99925 User Manual
Harman Kardon Stereo Receiver AVR 155 User Manual
Hearth and Home Technologies Indoor Fireplace SL 750TRSFHHIPI User Manual
Honeywell Thermostat 69 2072 05 User Manual
Hyundai Flat Panel Television 0090509536 User Manual
IBM Laptop Dock I User Manual
Ikelite Digital Camera 1030 SW User Manual
Impex Home Gym MD PWR 20 User Manual